Jak vyskočit mimo smyčku? níže program, jak používat goto nebo jakýkoli jiný program související se skokem

const int analogPin1 = A1; const int analogPin2 = A2; const int analogPin3 = A3; const int ledPin = 13; const int ledPin2 = 7; const int thresold = 400; unsigned int x1, x2, x3, fault = 0; void setup() { pinMode(ledPin, OUTPUT); Serial.begin(9600); } void Config() { delay(1000); Serial.print("ATE0r"); Response(); Serial.print("ATr"); Response(); Serial.print("AT+CMGF=1r"); Response(); Serial.print("AT+CNMI=1,2,0,0,0r"); Response(); } void Response() { int count = 0; Serial.println(); while (1) { if (Serial.available()) { char data = Serial.read(); if (data == "K") { Serial.println("OK"); break; } if (data == "R") { Serial.println("GSM Not Working"); break; } } count++; delay(10); if (count == 1000) { Serial.println("GSM not Found"); break; } } } void loop() { int analogValue1 = analogRead(analogPin1); int analogValue2 = analogRead(analogPin2); int analogValue3 = analogRead(analogPin3); if (analogValue1 < thresold) { x1 = 1; fault = x1; } if (analogValue2 < thresold) { x2 = x1 + 3; fault = x2; } if (analogValue3 < thresold) { x3 = x1 + x2 + 5; fault = x3; } switch (fault) { case 1: digitalWrite(ledPin, HIGH); Serial.print("AT+CMGF=1\r"); delay(1000); Serial.print("AT+CMGS=\"+919\"\r"); delay(1000); Serial.print("PHASE 1 HAS GONE"); delay(1000); Serial.write(0x1A); delay(1000); goto nsr; break; case 3: digitalWrite(ledPin, HIGH); Serial.print("AT+CMGF=1\r"); delay(1000); Serial.print("AT+CMGS=\"+919\"\r"); delay(1000); Serial.print("2 HAS GONE"); delay(1000); Serial.write(0x1A); delay(1000); goto nsr; break; case 4: digitalWrite(ledPin, HIGH); Serial.print("AT+CMGF=1\r"); delay(1000); Serial.print("AT+CMGS=\"+919\"\r"); delay(1000); Serial.print("1 AND 2 HAS GONE"); delay(1000); Serial.write(0x1A); delay(1000); goto nsr; break; case 5: digitalWrite(ledPin, HIGH); Serial.print("AT+CMGF=1\r"); delay(1000); Serial.print("AT+CMGS=\"+919\"\r"); delay(1000); Serial.print("3 HAS GONE"); delay(1000); Serial.write(0x1A); delay(1000); Serial.print("AT+CNMI=2,2,0,0,0"); goto nsr; break; case 6: digitalWrite(ledPin, HIGH); Serial.print("AT+CMGF=1\r"); delay(1000); Serial.print("AT+CMGS=\"+919\"\r"); delay(1000); Serial.print("1 AND 3 HAS GONE"); delay(1000); Serial.write(0x1A); delay(1000); goto nsr; break; case 8: digitalWrite(ledPin, HIGH); Serial.print("AT+CMGF=1\r"); delay(1000); Serial.print("AT+CMGS=\"+919\"\r"); delay(1000); Serial.print("2 AND 3 HAS GONE"); delay(1000); Serial.write(0x1A); delay(1000); goto nsr; break; case 10: digitalWrite(ledPin, HIGH); Serial.print("AT+CMGF=1\r"); delay(1000); Serial.print("AT+CMGS=\"+919\"\r"); delay(1000); Serial.print("ALL 3 HAS GONE"); delay(1000); Serial.write(0x1A); delay(1000); goto nsr; break; default: x1, x2, x3, fault = 0; digitalWrite(ledPin, LOW); break; } x1, x2, x3, fault = 0; digitalWrite(ledPin, LOW); do { int analogValue1 = analogRead(analogPin1); int analogValue2 = analogRead(analogPin2); int analogValue3 = analogRead(analogPin3); } while (analogValue1 < thresold || analogValue2 < thresold || analogValue3 < thresold); } do { int analogValue1 = analogRead(analogPin1); int analogValue2 = analogRead(analogPin2); int analogValue3 = analogRead(analogPin3); } while ((analogValue1 > th) && (analogValue2 > th) && (analogValue3 > th)); } nsr : if ((analogValue1 > th) && (analogValue2 > th) && (analogValue3 > th)) { digitalWrite(ledPin, HIGH); Serial.begin(9600); Serial.print("\r"); delay(1000); Serial.print("AT+CMGF=1\r"); delay(1000); Serial.print("AT+CMGS=\"+919\"\r"); delay(1000); Serial.print("ALL 3 Phase Restored"); delay(1000); Serial.write(0x1A); delay(1000); Serial.print("\r"); delay(1000); Serial.print("AT+CMGF=1\r"); delay(1000); Serial.print("AT+CMGS=\"+919\"\r"); delay(1000); Serial.print("ALL 3 Phase Restored"); delay(1000); Serial.write(0x1A); delay(1000); do { int analogValue1 = analogRead(analogPin1); int analogValue2 = analogRead(analogPin2); int analogValue3 = analogRead(analogPin3); } while ((analogValue1 > th) && (analogValue2 > th) && (analogValue3 > th)); } 

Komentáře

• Váš kód prosím naformátujte správně. Nemohu ' sledovat, co k tomu patří.
• Ano, ošklivý kousek špagetového kódu (opravdu pěkně řečeno).
• A po použití formátovače C ++ je ' zcela zřejmé, proč může ' nefunguje
• Jen pro měnovost x1, x2, x3, fault = 0; se má tyto proměnné nastavit na nulu? Mám pro vás špatné zprávy.